Arthrodesis plates

... individually is possible. Advantages - Comprehensive plating System - Two plates and three screw styles offer distinct implant combinations - One intuitive instrument set - Thin 2 mm plate design - ...

... Features - Self-locking screws - Oversized revision screws - Plate marking for easier plate size selection and placement - E-Plate (Extension to the existing ABC plate) - ...

Length: 21, 80 mm
Number of holes: 8, 4 unit

Anterior Cervical Locking Fixation System (VI) Application: For anterior cervical internal fixation

Length: 22, 72 mm

The Origin anterior plate serves to stabilize the cervical spine. Its locking system is particularly impressive, enabling two placed screws to be locked with one twist. -Pre-curved plate with locking ...

Length: 22, 30, 32, 50, 71 mm
Thickness: 1.8 mm
Number of holes: 4, 6, 8 unit

Anterior Cervical Plate-II System - Low profile design, plate thickness is 1.8mm - Unique observing window on the plate, helps checking the implant status - Screws on the coronal ...

Length: 39 mm

- Compression technology - Variable angle locking technology - Anatomical and special surgical implant

Number of holes: 4, 8, 6 unit

... spondylolisthesis caused by fusion failure. -Non limiting system;large viewport; visible endplate; self-taooing screw; low profile plate with locking device; screw guide system. (You could see all spine products in ...

Number of holes: 4 unit

Anterior Ankle Fusion Plate Product Introduction 1.Anatomic design is good for reduction, and no need to pre-bend the plate duringsurgery to avoid effect on the plate strength when ...

Number of holes: 5, 6 unit

Metatarsophalangeal Joint Fusion Plate I Product Introduction 1.Anatomic design, 9° dorsal flexure, and 11°extorsion, to avoid effect on the plate strength while it is bendedduring surgery. 2.Plate ...

Length: 23, 25, 27, 19, 21 mm
Thickness: 1.8 mm
Number of holes: 4, 6 unit

... Anterior Cervical Plate I, 4 Holes, 25mm Anterior Cervical Plate I, 4 Holes, 27mm Anterior Cervical Plate I, 4 Holes, 29mm Anterior Cervical Plate I, 6 Holes, 27mm Anterior ...

... feature Anatomical Fit Low-profile Plates provides minimum irritational Allows final screw fixation after compression is achieved 1 st MTP Plates: low-profile plates designed ...

... Pre-Lordosed Plate Round-edge, low profile plate and construct(2.0mm) Small stature width and profile. Optimized geometry for fit and performance(Durabilty &Fatigue strength) Surgical Versatility Semi ...

Hole diameter: 3.5 mm
Number of holes: 8 unit

Screws Used Ø3.5 Cortical Screw & Ø3.5 Locked Screw

Thickness: 1.2 mm

• The plates are bended according to the bone’s natural shapes.

Thickness: 1.5 mm

• The plates are bended according to the bone’s natural shapes.

Thickness: 1.8 mm

• The plates are bended according to the bone’s natural shapes.

• Provide high strength with low thickness • Provide effective and simple use • Low profile (totally 2 mm) • Flexible blocking system securely to the screw

• Straight Plate ,self-locking screws, nuts and washers create a rigid fixation

Hole diameter: 2.7 mm
Number of holes: 4, 14 unit

... Astrolabe’s Midfoot 2,7 is indicated for MP Joint 1 Arthrodesis and Revisions, MP Joint 1 Iliac Crest Arthrodesis, Metatarsal Arthrodesis and Lisfranc Arthrodesis, Interposition ...

Hole diameter: 3.5 mm

The Astrolabe’s Plantar plate is indicated for plantar Lapidus Arthrodesis as an evolved version of hallux valgus correction at certain angular degrees in order to prevent progression of arthrosis in ...

Hole diameter: 2.7, 3.5 mm

... fixation and is indicated for Keller-Brandes Revisions, MTP 1 lengthening arthrodesis, Revision after MTP 1 prosthesis and MT 1 lengthening osteotomy. This anatomically shaped plate allows facilitated ...

Number of holes: 20 unit

Elbow ( Arthrodesis ) Plate Ø 3.5 - Ø 4.0 mm screw

Number of holes: 8 unit

Hand Carpus ( Arthrodesis ) Plate Ø 3,5 - Ø 4.0 mm screw

Length: 118, 102 mm
Thickness: 3.5 mm

345.1330340.15 - Ø3.5/Ø4.5/Ø5.5//Ø6.5 Anterior Ankle Fusion VA-LCP(AA-TT),Short,Left 345.2330340.15 - Ø3.5/Ø4.5/Ø5.5//Ø6.5 Anterior Ankle Fusion VA-LCP(AA-TT),Short,Right 345.1330440.15 - Ø3.5/Ø4.5/Ø5.5//Ø6.5 Anterior Ankle Fusion VA-LCP(AA-TT),Long,Left 345.2330440.15 ...

Length: 102, 118 mm
Thickness: 3.5 mm

345.1200340.15 - Ø3.5/Ø4.5/Ø5.5//Ø6.5 Posterior Ankle Fusion VA-LCP(PA-TTC),Short Left 345.2200340.15 - Ø3.5/Ø4.5/Ø5.5//Ø6.5 Posterior Ankle Fusion VA-LCP(PA-TTC),Short Right 345.1200440.15 - Ø3.5/Ø4.5/Ø5.5//Ø6.5 Posterior Ankle Fusion ...

... .5 Anterolateral Tibiotalar Fusion VA-LOC Plate 345.1320835.15 - Ø4.5/Ø5.5 Anterolateral Tibiotalar Fusion VA-LOC Plate(ALA-TT),Long,Left 345.2320835.15 - Ø4.5/Ø5.5 Anterolateral Tibiotalar Fusion VA-LOC ...

Thickness: 5 mm
Number of holes: 6, 7 unit

ARIX CARPAL FUSION PLATE provides a specially designed solution for carpal bone fracture and management. Product Features • Fixing four-corner bones of carpal • Ø2.5mm Srews(locking/non-locking) Easy positioning ...

... • The plate and the screw are fixed to hold the adjusted shape of the distal tibia after the osteotomy • Reduced thickness for less irritation • The Anterior Ankle Fusion Plate is indicated ...

The FlexWing Anterior Cervical Plate System is intended for anterior vertebral screw fixation of the cervical spine at levels C2-T1. The System is indicated for temporary stabilization of the anterior spine during ...

The fixed titanium plate is made of TA3G pure titanium material conforming to the GB/T13810 standard, and the screw is made of TC4 titanium alloy material conforming to the GB/T13810 standard. The surface of the fixed ...

Length: 22.5, 27.5, 40, 52.5, 70 mm
Number of holes: 4, 8, 6 unit

Used for Instability and Slipping caused by trauma, degenerative diseases, tumors, spinal cancal stenosis, cervical instability and failed fusion surgery.

Length: 53, 17 mm
Thickness: 1.2 mm
Number of holes: 4, 6, 8, 12, 16 unit

The SurgTech Trauma System is a plate and screw fixation system. Plates and screws are offered in “mini”,“small” and “large” set sizes in a variety of shapes based upon the anatomical fixation required. Features It ...

Pr. Goutallier’s vertabral U-plate in Titanium Lumbar spinal plate

Pr. Goutallier’s vertabral U-plate in Titanium with intermediate claw

Pr. Goutallier’s vertabral U-plate in Titanium Dorsal spinal plate

• Titanium alloy material providing high strength with low thickness • Blocking system preventing the screw displaced • Titanium alloy self-tapping screws • Five different length options with two different diameters

Number of holes: 6 unit

Can be used for one or more segments Quite thin plate No height on the plate

Length: 20, 100 mm
Thickness: 2 mm
Number of holes: 8, 10, 4, 6 unit

S33 Spine Cervical Plate System is designed to meet the clinical expectations of anterior cervical surgery and it offers a wide range of plates and screw sizes. Low profile (2,0 mm) pre-bended plates Single ...

The system is indicated for use in cervical fusion procedures with or without tasarimmed cervical cage systems in skeletally mature patients with degenerative disc disease (DDD) from the C2 to C7 disc. Features: Anatomical shape Wide ...

... is carried out using a minimized spreader with variable approaches to the base and top plates or after fixation of one side of the plate in case of destroyed plate structure of the vertebral ...

... Anterior Cervical Stabilization Semi-rigid design with large angle variability Lockable, self-drilling screws Low profile plate design of 1.8 mm A cervical plating system must provide the cervical spine C2 - C7 with ...

... design with large angle variability Mono- and bicortical screw fixation Thin plate design of 1.6 mm TOSCA® Standard is designed according to the principle of semi-rigid plate and screw connections and ...

Length: 20, 100 mm
Thickness: 2 mm
Number of holes: 4, 6, 8, 10 unit

Prodorth Cervical Plate System is designed to meet the clinical expectations of anterior cervical surgery and it offers a wide range of plates and screw sizes. Low profile pre-bended plates Single ...

Length: 28, 35, 45 mm
Thickness: 2.7 mm
Number of holes: 5, 6 unit

FOREFOOT PLATING SYSTEM 2.7 4001080 5 - holes 28 mm, small size 4001081 6 - holes 35 mm, 10° valgus angle, medium size 4001082 6 - holes 45 mm, 10° valgus angle, large size

TITANIUM RECONSTRUCTION PLATE 4001025 35 mm 4001026 40 mm

TITANIUM UNIVERSAL PLATE 4001016 10 mm 4001017 12 mm 4001018 14 mm 4001019 16 mm 4001020 18 mm 4001021 20 mm 4001022 22 mm 4001023 24 mm 4001024 30 mm