Drill bits

Form drill PROGRESSIVE-LINE resterilizable Material Stainless steel

SURGICAL DRILL POINT PILOT 1.1 x 17mm ( 3 - 6 - 9 -12mm )

Available drills engineered for accurate model drilling according to the removable pin in use. Zeiser type cone-shaped drill Pindex type twin section drill Stem diameter: mm 3.00

Connection: - Conical Connection, Internal Hexagon Implant type: - C1, SEVEN, V3 Drill type: - Build-in stoppers, Pilot drills Length: - 31.8mm Diameter: - 2.4mm Material: - Stainless steel

... is designed to be used with the Drill sleeve instrument The depth markings can be read on the Drill tap shaft at 5 mm increments, when used with the Drill sleeve The Drill ...

... direct cut BIO | Cut drills have a special design with vastly improved cutting efficiency. Sequential drilling with the use of multiple drills in guided surgery is not needed. Thus, only the final osteotomy ...

... irrigation. drills • Drills are made of surgical grade Stainless Steel. • All drills are color coded for diameter. • Drill depth is identified by corresponding groove ...

Length: 4.5 mm - 10 mm

Delta offers a variety of Cannulated Drill Bits and Headed Drill Bits for various techniques and surgical approaches, creates the quality tunnels and sockets for the surgery.

Flatten surface of alveolar ridge The recommended rotation speed is600-800rpm.

Length: 1.3 mm

VS181 - Micro Series Veterinary Drill Bit Ø 1.3 mm

Implant Drills, Available in various size options. Ref: 25-111-012 (2.0mm) Ref: 25-111-013 (2.5mm) Ref: 25-111-014 (2.8mm) Ref: 25-111-015 (3.2mm) Ref: 25-111-016 (3.65mm) Ref: 25-111-017 (4.2mm) Ref: 25-111-018 ...

... Additional laser marking inside the grooves. SIZES Diameters: 2—2,5—2,75—3—3,35—3,5—3,75—4—4,35—4,5—4,75 Lengths: 28—36—39 mm Drills for Short implants: 5—5,5—6 mm in diameter

... Endostar Gates Glidden drills are engine-driven istruments and they are used to enlarge root canals orifice and coronal third of the canals. These instruments represent the oldest forms of root canal instruments. Gates ...

Length: 28, 32 mm

1-Single file to complete the preparation 2-Unusually sharp section of chip and chip evacuation enhanced 3-The capacity 4-More flexible than the traditional single file , indications broader A-Good variable pitch design for quick and ...

... Sequence BHI Drill Quality All drills are manufactured from high quality surgical materials Drills are marked by laser for easy identification Depth marks are shown with grooves and ...

Length: 145, 220 mm

1-0012 : 0 3.2mm Total - length 145 mm 1-00164: 0 3.5 mm Total - length 220 - mm 1-0019: 0 4.0mm Total - length 220mm

... -harvesting RBS® drills were developed and tested in hospitals. They are specially designed to ease the IDCAM and IDBIO implant placement. FEATURES The lower section incorporates along cutting thread and tapers to a ...

Spiral Ø 7 mm 2.2X 180 mm cannulated shaft: AO Spiral Ø 8 mm 2.2 X 180 mm cannulated shaft: AO Spiral Ø 9 mm 2.2X 180 mm cannulated shaft: AO Spiral Ø 9 mm 3.8 X 280 mm cannulated shaft: AO Spiral Ø0 10 ...

TAPS FEATURES •Material: stainless steel •Scope: surgery, treatment, thread forming •Maximum rotation speed: 25 rpm / with irrigation •Maximum number of uses: 45 uses DESCRIPTION It is recommended the use of taps in the ...

Différent heat treatments are available: E-FLEX PATH Silver/ Gold / Blue Features of E-FLEX EDGE superior flat-sided design Excellent cutting efficiency, shorten the time for preparation Better resistance for cyclic fatigue Decrease ...

... fixture. When placing a ORBIT fixture in soft bone (D IV) the surgeon should consider undersizing osteotomy. The final drill diameter should be limited to the one immediately smaller than the diameter that should ...

... diameter of each drill is color-coded as well as etched on the upper portion of the drill. The depth markings are both milled and etched. Every diameter of the parallel drill has five ...